Virtual ICT 1301

ICT 1301 glossary

What is the IAS? A drum store? An order-pair? The terms used on these pages, explained.

The ICT 1301 comes from a time before much of today’s computing vocabulary was settled, so its manuals, and these pages, use some unfamiliar words. Here they are, grouped by topic, with every term listed A to Z below.

The machine

1300 series
The range of ICT computers the 1301 belongs to: cost-efficient workhorses for commerce, for jobs such as payroll and accounting. Around 180 were built in the early 1960s. See hardware.
Batch processing
Running a job on a large file of data in one go, such as a whole company’s payroll, rather than one item at a time while someone waits. Typical work for the 1301, usually with the data on magnetic tape.
CPU (central processor)
The part of the computer that carries out the program: the mill, the registers and the control circuits. The 1301’s CPU also controls the peripherals directly.
Flossie
ICT 1301 serial number 6, the machine Virtual ICT 1301 simulates, and the first 1301 delivered to a customer. She is the oldest original second-generation electronic stored-program computer in the UK, and is now in storage at The National Museum of Computing.
Galdor
Galdor Computing, whose programmers worked with Flossie and made changes to her over the years, such as adding the Mill Switch. Virtual Flossie has been updated with their help to match these changes.
Germanium transistor
An early kind of transistor, made from germanium rather than the silicon used today. The 1301 has about 7,352 of them (and a single valve), which produce a lot of heat.
ICT
International Computers and Tabulators, the British company that built the 1301.
Mill
The arithmetic unit: the part of the computer that does the calculations. The name goes back to Charles Babbage’s Analytical Engine.
Mill Switch
A physical switch that sets how the mill does its arithmetic: Sterling, Decimal or Hex. It isn’t a standard 1301 part: Galdor added it to Flossie, using spare boards. As it is a switch, a program can’t change it. In the simulation it is in the Options menu (top right), set to Sterling to start with; Zork needs it set to Hex.
Second-generation computer
A computer built with transistors instead of the valves (vacuum tubes) of the first generation. The 1301 was one of the machines that marked the move from one to the other.
Sterling arithmetic
Calculating in pounds, shillings and pence, Britain’s money until 1971: 12 pence to the shilling and 20 shillings to the pound. As well as ordinary decimal arithmetic, the 1301 has an alternative set of functions that work in sterling, which made it popular with British businesses.
TNMOC
The National Museum of Computing, at Bletchley Park, where Flossie is now kept in storage.
Valve
A vacuum tube: a glass tube that switches or amplifies an electric current, used in first-generation computers such as Colossus. Valves are larger, hotter and less reliable than transistors. The 1301 has a single valve.
Wire-wrap
A way of making connections by winding a wire tightly round a square pin, without solder. The 1301’s circuit boards don’t plug in, so changing a faulty board meant undoing and remaking up to 25 wire-wrap connections.
Word
The unit the 1301 stores and works with: 12 decimal digits, each held in 4 bits, so 48 bits in all. One word holds a number, or a pair of orders. Store sizes are given in words: 2,000 words of IAS is about 12 kilobytes.

Storage

Backing store
Larger, slower storage behind the main memory, like a hard disk today. On the 1301 this is the drum store, and on bigger systems magnetic tape as well.
Core store
Memory made of thousands of tiny rings (cores) of ferrite, a magnetic material, threaded on a grid of wires. Each core is magnetised one way or the other to store one bit, and keeps it when the power is off. The 1301’s core store is its IAS.
Drum store
A spinning metal cylinder coated with magnetic material, with read and write heads along its length. The 1301’s drums are its backing store, each holding 12,000 words (Flossie has three). Words are read and written ten at a time, a decade, in about 18 ms. The first drum also holds Initial Orders.
Drum decade
A group of ten words on a drum, which are read or written together in a single transfer.
DTU (Data Transfer Unit)
Part of the optional, buffered magnetic tape subsystem, which contains almost as many logic circuits as the basic machine and roughly doubled its cost.
IAS (immediate access store)
The 1301’s main memory, what we would now call RAM: 2,000 words of fast core store, about 12 kilobytes. Programs run from the IAS, and addresses in it are four decimal digits, 0000 to 1999.
Magnetic tape
Large reels of tape, read and written by tape drives, for holding big files of data. Up to eight drives can be connected. The 1-inch tape units hold about 1.5 million words each (around nine megabytes); the simulation also models the half-inch tape system. Data on tape is written in blocks.
Overlay
Part of a program kept on the drum and only read into the IAS when it is needed, replacing another part. It lets a program bigger than the IAS run.
Store
The 1301’s word for memory: the IAS is the main store and the drums the backing store.
Store viewer
Part of the simulation, not the real machine: press N, or choose Store Viewer in the Options menu, to see the data in the IAS and drums, for debugging.
Tape block
A batch of words written to magnetic tape in one go. The tape stops between blocks. (Not the same as a program block.)
Writing ring
A ring fitted to a reel of magnetic tape to allow writing to it. Without the ring the tape can only be read, so it can’t be overwritten by mistake.

Input and output

Card pack
A stack of punched cards holding a program or its data. In the simulation, card packs are chosen from the drawers under the Programs icon.
Card punch
The machine that makes new punched cards from the computer’s output, at 100 cards a minute. In the simulation it is the machine at right angles to the rest, at the far left.
Card reader
Reads punched cards into the computer, at 600 cards a minute. Cards go in the input hopper on the right and come out in the output hopper on the left.
Flexowriter
The Friden Flexowriter, an electric typewriter connected to the computer, so a person can type to a program and the program can type back, at ten characters a second, in upper and lower case. Zork is played on it.
Hopper
The tray that holds cards waiting to be read or punched (the input hopper) or cards that have been (the output hopper).
Line printer
A printer that prints a whole line at a time: 120 characters wide, at 600 lines a minute.
Peripheral
A machine connected to the computer for input or output: the card reader, line printer, card punch, tape drives and Flexowriter. The basic 1301 has the first three. The CPU controls them closely, without a buffer between them, which saved a lot of circuitry and so cost.
Punched card
A stiff paper card that holds data as a pattern of holes. The 1301 uses 80-column cards: each of the 80 columns holds one character, coded by where the holes are punched. Programs and data were punched onto cards before being read into the computer. See programming the ICT 1301.

The console

Arithmetic registers (A, B and C)
Three registers, shown as lights at the top of the console, that each hold a 12-digit number for the computer to work on. Register A is mostly used to move data to and from the IAS and drums, B is the workhorse, and C is mostly used for reading cards. A dial chooses which one the lights show, and the dials and Set button below let you enter a number by hand.
Auto Manual dial
Sets how the computer runs: Auto runs a program at full speed; Manual runs one instruction each time Start is pressed; Repeat Manual steps on by itself at a fixed 3 instructions a second, slowly enough to watch what a program is doing.
Clock Selector
A dial on the console that selects the manual pulse. It isn’t working in the simulation yet.
Console
The control desk, where the operator sits. It shows the registers and indicators as lights, and has the switches, dials and buttons for starting, stopping and stepping through programs and for entering values by hand.
Control registers (1, 2 and 3)
Three program counter registers, which show the next instructions to be run as six-digit values. A dial on the console chooses which one is shown. When a program has loaded correctly, control register 3 shows 111111.
Hold CR and Circ + 1
Two positions of a switch on the console. Circ + 1, the normal setting, makes the computer fetch the next instruction from the store after each one. Hold CR (Hold Control Registers) keeps the instruction in control register 1, so each press of Start obeys the same instruction again: a way to give the computer single instructions by hand. See Tutorial 1.
Indicator
A single on/off value the computer and programs can test. There are three kinds: automatic (00 to 09), set by the computer, its peripherals or the mill; programmed (10 to 19), set and unset by the program; and manual (20 to 29), set by the operator with switches on the console.
Automatic indicators
Indicators 00 to 09, usually set by the computer, a peripheral or a result from the mill. Indicator 00 is always set, so testing it gives an unconditional jump.
Manual indicators
Indicators 20 to 29: ten switches on the console that a program can read but not change, so the operator can steer a running program. For example, the timing test program pauses while switch 29 is set.
Programmed indicators
Indicators 10 to 19, set, unset and tested by the running program, like Boolean variables. Each has a light in the centre of the console.
Initial Orders button
Sets up the control registers so that pressing Start loads Initial Orders from the drum into the IAS and runs it, ready to read a program from cards.

Programming

Address
Where a word is in the store: four decimal digits. In an order, the address is usually adjusted by the relativiser.
BCD (binary-coded decimal)
Storing each decimal digit separately, in 4 bits, rather than converting the whole number to binary. The 1301 works in decimal this way; 4 bits can also hold the hexadecimal digits 10 to 15, which the Mill Switch makes use of.
Block
A section of a program, written as if it starts at address 0000. A senior programmer decided where in the IAS each block would finally go, so several programmers could each write their own block of the same program. See relativiser.
Block markers (X, Y and Z)
Special marks punched on the last card of a block: X normally marks the end of a block, Y the end of a library subroutine, and Z the last card of the program.
Control word
A line on the program sheet that isn’t an order for the computer but an instruction to Initial Orders as it loads the program, given by a letter in the designation. For example, B says where to store the block that follows, and P defines a positive number.
Designation
The first part of an order: a single character or digit. Together with the function, it gives the operation. For example, designation 8 means set a programmed indicator, 9 unset one, and 4 jump if an indicator is set.
Function
The second part of an order: a 2-digit decimal number, usually the operation to carry out. For example, function 66 adds 1 to a word of the IAS, and 00 does nothing.
Hexadecimal (hex)
Counting in base 16, with digits 0 to 9 then 10 to 15 (often written A to F). The 1301 normally works in decimal, but with the Mill Switch set to Hex its 4-bit digits can use the values 10 to 15 too.
Initial Orders
The 1301’s bootstrap program, kept permanently in a reserved part of the first drum. It is loaded into the IAS (at address 200) with the Initial Orders button, then reads a program in from punched cards and runs it. Its own manual is on the software page.
Instruction
On the program sheet, a numbered order-pair. The number lets other orders jump to it.
Jump
An instruction that changes which instruction is obeyed next. In the six digits of an instruction, a 4 in the third digit marks a jump: the first two digits are the indicator to test and the last three the address to jump to. If the indicator is set the computer jumps; if not, it carries on. Indicator 00 is always set, so 004000 is an unconditional jump to address 0000. Most jumps also click the loudspeaker, which programs used to make tones.
Machine code
Instructions written directly as the numbers the computer obeys. 1301 programmers didn’t use an assembler or a higher-level language: they wrote machine code by hand.
Order
A single command for the computer, made up of four parts: designation, function, address and relativiser.
Order-pair
Two orders stored together in one word. A card in the normal card form holds three order-pairs.
Program sheet
The printed form a programmer wrote a program on, one order per row, ready for it to be punched onto cards. Programs were usually drawn as a flow chart first. See programming the ICT 1301.
Relativiser
The last part of an order, saying which block its address is in. B means the current block; a number means another block. If the current block is stored at IAS 0200, address 0013 with relativiser B means 0213; move the block to 0600 and it means 0613, without rewriting the program.
Ten’s complement
How the 1301 stores negative numbers: minus one is 999999999999, and minus a thousand is 999999999000.
Z-machine
The imaginary computer Infocom wrote Zork for, so that the same game could run on any real computer with a small interpreter program. Virtual Flossie runs Zork with a Z-machine interpreter written in 1301 machine code. See Zork on Flossie.

The original manuals have their own reference tables and glossary in Part 6 of the Programmers Reference Manual. All the manuals are listed on the software page.